Can You Remove The Sides Of An Antique Makeup Vanity And Use Them As Night Stands

Tips and Tricks for creating your own unique nightstands from an onetime vanity.

Have you seen the fabulous furniture artisans out there who are updating broken downwardly antique vanities and creating 2 matching nightstands from them? (See our showtime set of vanity nightstands Here) Information technology's really hard to find two matching minor nightstands in the used piece of furniture world, only vanities are a chip more prevalent and hardly used "as is" anymore. Therefore you can create your very own matching small nightstands from an sometime vanity!

We will be honest with yous all though, this isn't quite a beginner DIY projection. Some of the old vanities are fairly simple to actually take apart and some that have a full top are a flake more than intense. Only no matter what kind of vanity you find, like shooting fish in a barrel or harder to take apart, there is always some kind of fixing that needs to be done. Here is where the beginner could perhaps accept problems! Each one is unlike and sometimes you take to be creative in how you fix the pieces.

In this article, we are sharing just one style of antique vanity and how we took it apart and fixed it up for painting. At that place are quite a few styles this would piece of work on, some – like vanities that take ane continuous top – would have more to information technology.

Essentially you demand to commencement take a look at the piece to come across where it is joined. This vanities mirror slid right out at the acme but other styles could be screwed in, which makes it very easy to accept apart.

Once the mirror was off we could run into at that place were iii wooden bars on the back side that were all nailed into the back of this piece. It takes only a footling maneuvering and wiggling to get a apartment screwdriver or a small pry bar past the nails to pry them out!

In one case those bars were off, the vanity only had one other forest piece at the bottom that was connecting the 2 sides. Encounter, this item style is fairly like shooting fish in a barrel to accept apart! We did await inside to see if in that location were nails nosotros could run across there, only in that location wasn't, then Kristen just stood in between the ends and pushed them away from each other!

It was really just held together with a couple nails and some gum that was very old.

And at that place information technology was! We had two separate nightstands!

Again, that was the piece of cake office…

Side by side came the hard part of fixing it up and then both pieces looked the same on each side. There were nails sticking out of the side where the middle bar was and no way to pry them out since the heads were completely hidden on the within and then instead nosotros clipped them off with a wire clippers.

At that place was also a part in the back of each side of the nighstands (where the mirror sat) that had a footling lip. It wasn't flush all the way down. So we decided to rip downwards a very skinny slice of forest, then glue and nail it into those spots. Just like the pictures show. Then it was flush and matched the other side! We as well had to do quite a bit of filling. There was a bit to fill up forth the edge where we added the woods, and a bunch down below where the veneer was peeling off.

Peeling veneer isn't ever fun to piece of work with. Sometimes you tin can glue it back down but sometimes information technology just needs to come off. We merely literally pulled this part off and then had to make full quite a scrap with wood putty using a putty knife to get it very smooth. (At that place are so many kinds of wood putty you can use and I will brand sure to link to all of the products nosotros honey downwards below!)

But we weren't done yet! On the very top of the nightstands were trim pieces that went with the mirror. They had some beautiful details to them, even so once the mirror was gone they didn't make sense anymore! They didn't match on each side! And so nosotros had to pry the existing ones off – using the same flat screwdriver and a hammer this fourth dimension. Nosotros were then able to create our very own backplate slice out of a one x three that we just rounded on each side, then glued and nailed in.

There was quite a lot to practise to these pieces before paint could brainstorm as you tin encounter. But they are going to be totally worth it! If you are confident in your fixing abilities then we hope we helped y'all out with a few tips yous may non have known earlier! If you lot are new to this, accept your time on them – they will definitely be worth information technology!

Stay tuned with u.s.a. to see how these nightstands turn out in the next couple of weeks afterwards we get the pigment on!

Our Favorite Wood Fillers & Tools

Source: https://timelesscreationsmn.com/how-to-take-apart-an-old-vanity-for-nightstands/

Posted by: dotsonposelver.blogspot.com

Share this post